Skutt KS Kiln Unpacking Manuel d'utilisateur télécharger pdf (Page 1)

6441 SE Johnson Creek Blvd., Portland, OR 97206 Phone (503) 774-6000 Fax (503) 774-7833

www.skutt.com

TAB TEXT HERE

TAB TEXT HERE TAB TEXT HERE

PARTS INSTRUCTION SHEET

13.2 REV 05/20/05

REPLACEMENT PARTS

(continued)

1. Open the lid, remove the plastic cover and carefully remove the kiln stand and

“goodie bag” from the inside of the kiln. Models KS818-3 & KS614-3 have the

stand in a separate box. Close the lid.

2. Remove the black plastic feet from the “goodie bag” and put them on the stand

legs. Set the stand in the location you have designated for the kiln. See the section

in the owner’s manual on locating your kiln if you are not sure about the safety

requirements for the kiln site.

There are two options for setting the kiln up. The ﬁrst option is to remove the lid and set

it up as one unit. Option one is not recommended for 12 sided kilns because the additional

weight puts too much strain on the handles. Option two involves breaking the kiln into light-

er sections for easier handling. These options are discussed in detail below.

Option one.

1. For larger, heavier kilns you may choose to remove the lid from the top section.

This will reduce the overall weight. To do this remove one cotter pin from the lid

rod and slide the lid rod out of the lid hinge assembly. Also remove the

thumbscrew and lid brace.

2. Place the lid on a clean, ﬂat surface.

3. There are section handles on the kiln. With a partner, using the lower section

handles, lift the kiln off the kiln ﬂoor and rest it on a clean, ﬂat surface next to the

stand.

4. Position the kiln ﬂoor on top of the stand making certain that the weight is evenly

distributed.

Notes on assembly. Make sure the stand and kiln ﬂoor are level and do not teeter.

Leveling problems may put unnecessary stress on the kiln during ﬁring. To level

the stand, place ﬁrm shims under the legs (never between the stand and the

kiln). Kilns with Envirovents may be a little wobbly until after the ﬁrst ﬁring when

the kiln seats itself into the high temperature silicone rings.

5. Place the kiln on the slab making sure the edges are aligned.

6. Replace the lid on top of the kiln.

7. Replace the lid rod, cotter pin and the lid brace.

The kiln is now ready for use.

KS Kiln Unpacking

Instructions

1 2

Résumé du contenu

Page 1 - Instructions

6441 SE Johnson Creek Blvd., Portland, OR 97206 Phone (503) 774-6000 Fax (503) 774-7833www.skutt.comTAB TEXT HERETAB TEXT HERETAB TEX

Page 2 - Option two

TAB TEXT HERETAB TEXT HERE TAB TEXT HERE TAB TEXT HERE TAB TEXT HEREREPAIRSPARTS INSTRUCTION SHEET13.2 REV 05/20/05KS KILN UNPACKING INSTRUCTIONS CO

Commentaires sur ces manuels

Pas de commentaire

Skutt KS Kiln Unpacking Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Skutt KS Kiln Unpacking. Skutt KS Kiln Unpacking User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Skutt KS Kiln Unpacking Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Skutt KS Kiln Unpacking. Skutt KS Kiln Unpacking User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Skutt KS Kiln Unpacking